Login
Printed Circuit Board (PCB): A flat board made of sturdy materials such as FR-4. A PCB holds and connects electronic components with thin lines of metal, called traces, that allow electricity to flow between components. A PCB is the foundational piece of most modern electronics.
If you are looking for more details, kindly visit our website.
FR-4: The standard material for producing PCBs. FR-4 is a type of composite material made of woven fiberglass cloth and an epoxy resin.
Trace: An electrical pathway, usually made of thin copper lines, that connect different parts of a circuit on a PCB.
Via: A small hole that acts like a tunnel through a PCB and connects different layers of the board. It allows traces on one side to connect with traces on another, enabling three-dimensional connections.
Silkscreen: A printed layer on a PCB that provides labels, markings, and information about where each component should be placed and how it should be oriented.
Copper Layer: A very thin layer of copper that covers the surface of a PCB. Traces are created by etching away the excess copper from this layer, leaving behind the desired electrical pathways.
Ground Plane: A large area of copper on a PCB that serves as the reference point for electrical signals, ensuring all parts of the circuit are working in sync.
Power Plane: A large area of copper on a PCB dedicated to carrying electrical power to different parts of the circuit.
Pad: Pads are small areas of metal on a PCB where the leads of electronic parts are soldered, creating a secure electrical connection.
Annular Ring: A circular area of metal around a drilled hole on a PCB, which helps create a strong connection for components with leads.
Non-Plated Through-Hole (NPTH): Holes in a PCB that dont have copper plating. Often used for mechanical support or alignment.
Thermal Relief: A pattern of traces that connect a pad to a larger copper area, making it easier to solder components without overheating them.
SFUptownMaker
Contributors:
One of the key concepts in electronics is the printed circuit board or PCB. It's so fundamental that people often forget to explain what a PCB is. This tutorial will breakdown what makes up a PCB and some of the common terms used in the PCB world.
Over the next few pages, we'll discuss the composition of a printed circuit board, cover some terminology, a look at methods of assembly, and discuss briefly the design process behind creating a new PCB.
Before you get started you may want to read up on some concepts we build upon in this tutorial:
Minh Tun was kind enough to translate this tutorial to Vietnamese. You can view the translation here.
Printed circuit board is the most common name but may also be called "printed wiring boards" or "printed wiring cards". Before the advent of the PCB circuits were constructed through a laborious process of point-to-point wiring. This led to frequent failures at wire junctions and short circuits when wire insulation began to age and crack.
->
courtesy Wikipedia user Wikinaut <-
A significant advance was the development of wire wrapping, where a small gauge wire is literally wrapped around a post at each connection point, creating a gas-tight connection which is highly durable and easily changeable.
As electronics moved from vacuum tubes and relays to silicon and integrated circuits, the size and cost of electronic components began to decrease. Electronics became more prevalent in consumer goods, and the pressure to reduce the size and manufacturing costs of electronic products drove manufacturers to look for better solutions. Thus was born the PCB.
PCB is an acronym for printed circuit board. It is a board that has lines and pads that connect various points together. In the picture above, there are traces that electrically connect the various connectors and components to each other. A PCB allows signals and power to be routed between physical devices. Solder is the metal that makes the electrical connections between the surface of the PCB and the electronic components. Being metal, solder also serves as a strong mechanical adhesive.
A PCB is sort of like a layer cake or lasagna- there are alternating layers of different materials which are laminated together with heat and adhesive such that the result is a single object.
Let's start in the middle and work our way out.
The base material, or substrate, is usually fiberglass. Historically, the most common designator for this fiberglass is "FR4". This solid core gives the PCB its rigidity and thickness. There are also flexible PCBs built on flexible high-temperature plastic (Kapton or the equivalent).
You will find many different thickness PCBs; the most common thickness for SparkFun products is 1.6mm (0.063"). Some of our products- LilyPad boards and Arudino Pro Micro boards- use a 0.8mm thick board.
Cheaper PCBs and perf boards (shown above) will be made with other materials such as epoxies or phenolics which lack the durability of FR4 but are much less expensive. You will know you are working with this type of PCB when you solder to it - they have a very distictive bad smell. These types of substrates are also typically found in low-end consumer electronics. Phenolics have a low thermal decomposition temperature which causes them to delaminate, smoke and char when the soldering iron is held too long on the board.
The next layer is a thin copper foil, which is laminated to the board with heat and adhesive. On common, double sided PCBs, copper is applied to both sides of the substrate. In lower cost electronic gadgets the PCB may have copper on only one side. When we refer to a double sided or 2-layer board we are referring to the number of copper layers (2) in our lasagna. This can be as few as 1 layer or as many as 16 layers or more.
PCB with copper exposed, no solder mask or silkscreen.
The copper thickness can vary and is specified by weight, in ounces per square foot. The vast majority of PCBs have 1 ounce of copper per square foot but some PCBs that handle very high power may use 2 or 3 ounce copper. Each ounce per square translates to about 35 micrometers or 1.4 thousandths of an inch of thickness of copper.
The layer on top of the copper foil is called the soldermask layer. This layer gives the PCB its green (or, at SparkFun, red) color. It is overlaid onto the copper layer to insulate the copper traces from accidental contact with other metal, solder, or conductive bits. This layer helps the user to solder to the correct places and prevent solder jumpers.
In the example below, the green solder mask is applied to the majority of the PCB, covering up the small traces but leaving the silver rings and SMD pads exposed so they can be soldered to.
Soldermask is most commonly green in color but nearly any color is possible. We use red for almost all the SparkFun boards, white for the IOIO board, and purple for the LilyPad boards.
The white silkscreen layer is applied on top of the soldermask layer. The silkscreen adds letters, numbers, and symbols to the PCB that allow for easier assembly and indicators for humans to better understand the board. We often use silkscreen labels to indicate what the function of each pin or LED.
Silkscreen is most commonly white but any ink color can be used. Black, gray, red, and even yellow silkscreen colors are widely available; it is, however, uncommon to see more than one color on a single board.
Now that you've got an idea of what a PCB structure is, let's define some terms that you may hear when dealing with PCBs:
Examples of annular rings.
JYN Product Page
Not so accurate, but functional drill hits.
Mouse bites on the LilyPad ProtoSnap allow the PCB to be snapped apart easily.
Note: Looking for more information about mousebites and how to integrate it in your designs? Try checking out theLooking for more information about mousebites and how to integrate it in your designs? Try checking out the blog post below!
PTH (plated through-hole) pads on the left, SMD (surface mount device) pads on the right.
Abe does a quick demonstration of how to line up a paste stencil and apply solder paste.
Bob shows us the SparkFun MyData Pick and Place machine. It's pretty awesome.
Various portions of the PCB that have no traces but has a ground pour instead.
A PTH resistor inserted into the FabFM PCB, ready to be soldered. The legs of the resistor go through the holes. The plated holes can have traces connected to them on the front of the PCB and the rear of the PCB.
The popular pogo pin with pointed tip . We use tons of these on our test beds.
Silkscreen identifying this LED as the power LED.
Complex slots cut into the ProtoSnap - Pro Mini . There are also many mouse bites shown.the corners of the slots cannot be made completely square because they are cut with a circular routing bit.
Solder paste on a PCB shortly before the components are placed. Be sure to read about *paste stencil above as well.*
Solder mask covers up the signal traces but leaves the pads to solder to.
On the left, a solder pad with two small traces (thermals) connecting the pin to the ground plane. On the right, a via with no thermals connecting it completely to the ground plane.
-> A small trace connecting the Reset pad to elsewhere on the board. A larger, thicker trace connects to the 5V power pin. <-
Front and back of the same PCB showing a tented via. This via brings the signal from the front side of the PCB, through the middle of the board, to the back side.
How do you go about designing your own PCB? The ins and outs of PCB design are way too in depth to get into here, but if you really want to get started, here are some pointers:
Finally, a few words on the utility of designing your own circuit boards. If you plan on making more than one or two of a given project, the payback on designing a board is pretty good- point-to-point wiring circuits on a protoboard is a hassle, and they tend to be less robust than purpose-designed boards. It also allows you to sell your design if it turns out to be popular.
If you want to learn more, please visit our website FPC/PCB Pumice Line.
2 0 0
Join Us
Comments
All Comments ( 0 )